Project

General

Profile

Actions
History

Wiki

banc de gaz 2.0

Banc_de_gaz_20

Boitiers Capteur

Boitier TO

TO5 10 pin

Capteurs TO8
TO8 12 pin (PROPOSAL)

TO8 16 pin (ACTUAL)

TO8 16 pin (PROPOSAL)

Boitier PLCC Plastic Leaded Chip Carrier ou LCCC Leadless Ceramic Chip Carrier

PLCC Plastic Leaded Chip Carrier ou LCCC Leadless Ceramic Chip Carrier

boitier céramique

Number Leads Pitch Body Size Square Open Cavity Order Number
28 1.27mm (50 Mil) 11.5mm (0.45") CLCC28J50-N

https://topline.tv/ceramic.html

support

si pas de boitier céramique, alors on peut utiliser un PCB et un support male

sans boitier, bonding direct sur PCB

avec ressort

on doit pouvoir réduire le pas a 1.27mm

avec POGO

SMU PXIe-4142

SMU Specifications
Voltage Programming and Measurement Accuracy/Resolution
Voltage Programming and Measurement Accuracy/Resolution Range Resolution and noise (0.1 Hz to 10 Hz)
24 V 200 μV 0.1% + 10 mV 0.0005% + 1 μV

Accuracy (23 °C ± 5 °C) ± (% of voltage + offset),[2] Tcal±5 °C Temperature Coefficient ± (% of Voltage + Offset) / °C, 0 °C to 55 °C

Current
Current Programming and Measurement Accuracy/Resolution Range Resolution and noise (0.1 Hz to 10 Hz)
10 μA 100 pA 0.1% + 5.0 nA 0.002% + 10 pA
100 μA 1 nA 0.1% + 50 nA 0.002% + 100 pA
1 mA 10 nA 0.1% + 0.5 μA 0.002% + 1.0 nA
10 mA 100 nA 0.1% + 5.0 μA 0.002% + 10 nA
150 mA 1.5 μA 0.1% + 75 μA 0.002% + 150 nA

Accuracy (23 °C ± 5 °C) ± (% of current + offset), Tcal ±5 °C Tempco ± (% of current + offset)/°C, 0 °C to 55 °C

PXIe-4142 Pinout DB25 ♂

Signal Name Description
CH <0..3> Output HI HI force terminal connected to channel power stage (generates and/or dissipates power). Positive polarity is defined as voltage measured on HI > LO.
CH <0..3> Guard Buffered output that follows the voltage of the HI force terminal. Used to drive shield conductors surrounding HI force and Sense HI conductors to minimize effects of leakage and capacitance on low level currents.
CH <0..3> Output L LO force terminal connected to channel power stage (generates and/or dissipates power). Positive polarity is defined as voltage measured on HI > LO.
CH <0..3> Sense HI Voltage remote sense input terminals. Used to compensate for I*R voltage drops in cable leads, connectors, and switches.
CH <0..3> Sense LO Voltage remote sense input terminals. Used to compensate for I*R voltage drops in cable leads, connectors, and switches.
- NC No Connect.

⚠ ATTENTION LES MASSES COMMUNE DOIVENT CE FAIRE SUR LES -

RJ45

Version ACTUAL

Version COOL

Interconnexion

les "Heater" sont sur les "channel" pair.
les "Sense" sont sur les "channel" impair.
une carte NI PXI4142 gère 2 "Sensor" (Heater + Sense)

Channel SENSOR DB25 RJ45 ACTUAL RJ45 COOL
CHO HA+ 14 8 8
CHO HA- 16 7 7
CH1 SA+ 17 1 1
CH1 SA- 19 2 2
CH2 HB+ 20 3 3
CH2 HB- 22 7 6
CH3 SB+ 23 4 4
CH3 SB- 25 5 5
GUARD NC - *?*
SENSE NC - NC

https://www.ni.com/fr-fr/shop/model/pxie-4142.html

sucettes

double RJ45

Cette sucette s’avère trop complexe a construire

LEMO


LEMO-EGG.2K.316.CYM


LEMO_FGG.2K.316.CYCC65Z

Tulipe HARWIN série H31

HARWIN série H31

Code commande RS: 175-5234
Code commande Farnell: 3395113
Code commande Mouser: 855-H3175-01
Référence fabricant: H317501
Marque: HARWIN

Female Vertical Throughboard Ø0.50mm Contact

Fabricant HARWIN
Code commande Farnell:H3190-01
Code commande Mouser: 855-H3190-01
Référence fabricant: 3932934

Digital humidity and temperature sensor

SHT45

0 to 100 ±1.0% RH
–40 to +125 ±0.1°C

0x44 I2C addr.

https://sensirion.com/products/catalog/SHT45

https://docs.arduino.cc/libraries/artronshop_sht45/

Gas Sensor

CS811 vs SGP30, BME680

CS811 SGP30 BME680
power consumption
reproducibility and reliability yes yes yes
lifetime (year) 5 10 ?
baseline compensation algorithm compensation algorithm compensation algorithm
Sampling rate (s) 0.25-60 1-30 0.75-92

Sensirion Multi-Pixel Gas Sensor SGP

https://www.sensirion.com/en/environmental-sensors/gas-sensors/multi-pixel-gas-sensors/

SGP41

Air Quality Sensor for VOC and NOx Measurements

Ethanol in clean air 500 – 10’000 ppb
NO2 in clean air 50 – 650 ppb

I2C address 0x59

https://sensirion.com/media/documents/5FE8673C/61E96F50/Sensirion_Gas_Sensors_Datasheet_SGP41.pdf

https://docs.arduino.cc/libraries/sensirion-i2c-sgp41/

Référence Mouser 403-SGP41-D-R4

AGS10

TVOC Sensor

I2C address 0x1A

http://www.aosong.com/userfiles/files/Datasheet%20AGS10.pdf
https://github.com/gina-seth/AGS10_sensor

AMS CCS811 Gas Sensor (Obsolète)

eCO2 400ppm 32768ppm
eTVOC 0ppb 29206ppb

http://ams.com/eng/Products/Environmental-Sensors/Air-Quality-Sensors/CCS811

https://docs.arduino.cc/libraries/adafruit-ccs811-library/

Bosch BME680 is an integrated environmental sensor

Temperature -40°C 85°C ±0.5°C
Humidity 0% 100% ±3%
Pressure 300hPa 1100hPa ±1.0 hPa
Environment gas

I2C address 0x76 (SDO GND)
I2C address 0x77 (SDO VDD)

https://www.bosch-sensortec.com/bst/products/all_products/bme680

https://docs.arduino.cc/libraries/bme680/

Référence Mouser 262-BME680

Pressure

MS8607-02BA01 PHT Combination Sensor

SPECIFICATIONS
• Integrated pressure, humidity and temperature sensor
• QFN package 5 x 3 x 1 mm3
• Operating range: 10 to 2000 mbar, 0%RH to 100%RH,
-40 to 85 °C
• High-resolution module: 0.016 mbar, 0.04%RH, 0.01°C
• Supply voltage: 1.5 to 3.6 V
• Fully factory calibrated sensor
• I2C interface

Adresses I2C: 0x76 et 0x40

https://redmine.laas.fr/documents/261

code pour esp8266 : https://redmine.laas.fr/attachments/5184

la carte D1 mini n'est pas reconnue par NIMAX (problème de driver ?)

Code pour ARduino UNO : https://redmine.laas.fr/attachments/download/5195/ms8607_UNO.zip

Commande Réponse
H ou h Humdity [ 28.18 % ]
P ou p Pression [ 986.44 hPa ]
T ou T Temperature [ 23.58 C ]
V ou v version PHT250313

câblage

UNO ESP MS8607
3.3V VDD 3.3V
GND GND GND
A5 SCK D1 GPIO5 SCL
A4 SDA D2 GPIO4 SDA

Updated by Frédéric Blanc about 1 year ago · 81 revisions