Wiki DLP4100

Overview¶

The DLP® Discovery™ 4100 (D4100) is the latest in a series of spatial light modulation development kits from Texas
Instruments. Users of the D4100 Starter Kit have the ability to manipulate visible, ultraviolet and near-infrared light
with extremely high performance and high resolution.
The D4100 offers developers a flexible platform to design products to fit most any application using the proven
reliability of DLP technology.

Fig 1: System Overview

New version	Actual	Name
DLPC410	DDC4100 (FPGA X5VLX30)	Digital Controller for Discovery 4100 chipset
DLPR410	XCF16P	PROM for Discovery 4100 chipset
DLPA200	DAD2000	DMD Micromirror Driver

DLPC410 DLP Digital Controller [dlps024c.pdf]

Configuration Jumpers, Switch and LED¶

Fig 2: D4100 Controller Configuration Jumpers, Switch and LED

LED1 - USB status¶

CY7C68013A_128

LED2 - APPSFPGA status¶

(FPGA PIN N14)

LED	Status
RED	BAD
GREEN	OK

LED3 - DDC4000 status¶

LED	Status
RED	BAD
GREEN	OK

LED9..12 - LED status¶

LED9 - DDC_LED0 Status LED for the DDC4000
The LED9 signal is typically connected to an LED to show that the DLPC410 is operating normally.
The signal is 1 Hz with 50% duty cycle, otherwise known as the heartbeat

LED10 - DDC_LED1 Status
LED for the DDC4000. The LED1 signal is typically connected to an LED indicator to show the status
of system initialization and the status of the clock circuits. The LED1 signalis asserted only
when system initialization is complete and clock circuits are initialized. Logically, these
signals are ANDed together to show an indication of the health of the system. If the Phase Locked
Loop (PLL) connected to the data clock and the DMDclock are functioning correctly after system
initialization, the LED will be illuminated

LED11 - VLED0 This logic is to be defined by the APPSFPGA application. Drive low to turn on the led. Drive high to
turn off the led(FPGA PIN AK19).

LED12 - VLED1 This logic is to be defined by the APPSFPGA application. Drive low to turn on the led. Drive high to
turn off the led(FPGA PIN AJ19).

JUMPERS¶

J2 – EXP Voltage Select

J4 – Used to select the revision of firmware loaded from the PROM to the APPSFPGA.

Jumper Position	Revision Version
open	0
close	1

J5 – Shared USB signal disabled

Jumper Position	USB Signals
0-1	Disconnected from FPGA
1-2	Connected to FPGA
2-3	Automatically connect USB signals to FPGA when USB is connected to host PC

J7 – USB EEPROM Programming Header

Used to temporally disconnect the USB EEPROM fromthe device so the device can load its internal
boot loader rather than any code in the EEPROM. Install J8 for Cypress internal boot loader.

J10 – DAD2000 B Output Enable

Used to enable the outputs for DAD2000 B. This needs to be enabled only if using the 1080p DMD,
otherwise this can be disabled.

Jumper Position	DAD2000 B Outputs
open	Disabled
close	Enabled

J11 – Used to select the revision of firmware loaded from the PROM to the DDC4100 (FPGA X5VLX30).

Jumper Position	Revision Version
open	0
close	1

SWITCH¶

SW1 - Dipswitches

Functionality defined by APPSFPGA programming. In default test pattern code:

Switch Number	Effect	FPGA PIN
1	ON = float – float all mirrors	G20
2	ON = counter halt – stop counter, this will freeze the image on the DMD	G21
3	ON = complement data – causes DDC 4000 to complement all data it receives	F20
4	ON = north/south flip – causes the DDC 4000 to reverse order of row loading, effectively flipping the image	G22
5	Dictates the type of reset being used LSB ON = 1	H15
6	Dictates the type of reset being used MSB ON = 1	H14
	00 : single block phased reset
	01 : dual block phased reset
	10 : global reset
	11 : quad block phased reset
7	ON = Row Address Mode	H12
8	ON = WDT Enable, disables other resets	J14

SW2 - Push Button Momentary Switch

Functionality defined by APPSFPGA. This switch is used for APPS_LOGIC_RESET in the default code.
(FPGA PIN T24)
SW3 - Push Button Momentary Switch

Functionality defined by APPSFPGA. This switch is used for APPS_LOGIC_MIRROR_FLOAT in the default code.
(FPGA PIN P10)
SW4 - POWER STANDBY

Power Down¶

To ensure long term reliability of the DMD, a shutdown procedure must be executed.
Prior to power removal, assert the PWR_FLOAT (Table 1) signal and allow approximately 300μs for the procedure to
complete. This procedure will assure the mirrors are in a flat state. For more details, please refer to the
appropriate DMD document.

APPSFPGA¶

The APPSFPGA contains the Applications FPGA Sample Code for the DDC4100. This sample code
cycles through test patterns and is meant to offer an example of code that meets the DDC4100
specification. It has been written to implement all features of the DDC4100, such as the complement
function and all mirror reset types, as explained in later sections. This sample code also addresses
additional operational requirements for the DDC4100 interface which should be observed.

Signal Name	Description
CLK_I	Input clock (50 MHz)
ARSTZ	Active low, asynchronous system reset (connected to flip switch)
IN_PWR_FLOAT_I	Float all mirrors in preparation for system shutdown (connect to push-button switch)
FINISHED_IV_O	Indicates when applications FPGA has finished initialization (connected to LED)
IN_RST_ACTIVE_I	Asserted while a mirror reset is being executed
IN_INIT_ACTIVE_I	Asserted while DDC4100 is initializing
IN_DIP_SW_I	Dip switch inputs
FINISHED_IV_O	Indicates when applications FPGA has finished initialization (connected to LED)
CLK_R	Reference clock to DDC4100 (50MHz)
DOUT_A[15:0]	Output data A to DDC4100 (400MHz DDR)
DOUT_B[15:0]	Output data B to DDC4100 (400MHz DDR)
DOUT_C[15:0]	Output data C to DDC4100 (400MHz DDR)
DOUT_D[15:0]	Output data D to DDC4100 (400MHz DDR)
DCLK_A	Output data clock to DDC4100 (400MHz)
DVALID_A	Output data valid to DDC4100 used to qualify data
ROWMD[1:0]	Output row mode to DDC4100
ROWAD[10:0]	Output row address to DDC4100
STEPVCC	Output to indicate status of vcc step
COMP_DATA	Output to cause DDC4100 to complement all data
NS_FLIP	Output to cause DDC4100 to reverse order of row loading
BLKAD	Output block address to DDC4100
BLKMD	Output block mode to DDC4100
WDT_ENABLEZ	Output watch dog timer

Getting Started
The following steps should be followed in starting board operation using the default APPSFPGA code installed at the
factory :
1.) Connect 5V, 5 A power supply to the supplied power cable. Connect the power cable to J12 with the power
supply OFF.
2.) Confirm all SW2 switches are in the OFF position. Confirm all 5 H1 jumpers are in place. If using a 1080p
DMD confirm J11 is installed.
3.) Connect the DMD to the board with the flex cable(s). One flex cable attached to J13 is used for XGA DMDs,
two flex cables attached to J14 and J14 are used for 1080p DMD.
4.) Turn the power supply ON. D2 and D3 should briefly display red then green to indicate APPSFPGA and
DDC4000 configuration. D9 should flash green at 1 Hz. D10 should display green. The DMD will repeatedly
cycle through several test patterns.

To stop operation :
1.) Press SW3 to float the DMD, then turn power OFF.

DDC4100 Applications FPGA Sample Code Guide [2510445.pdf]

DDC4100 GUI/MEM Applications FPGASample¶

fig. System Overview of Example Design

fig. GUI/MEM APPS FPGA Block Diagram

Switch Number	Effect
1	Inject error into the Memory BIST
2	Unused
3	Unused
4	Unused
5	Unused
6	Unused
7	Unused
8	Unused

MEM APPS Design
The DDR2 MEM APPS FPGA design contains sample code for testing a 2GB DDR2 SO-DIMM module at
150 MHz with a burst length of four. The DDR2 module has a 64-bit data interface. The target device
used in this design is the MT16HTF25664HY-667. The design consists of two blocks: Memory_BIST and
Memory Controller.
Applications FPGA design that drives the DDC4100 system via USB/GUI [2510445_GUI.pdf]

EXP Expansion Connectors¶

To connect to an Avnet EXP compatible motherboard product.
Board design includes additional LVDS pairs to support 64 bit LVDS connection through EXP
connectors with a custom interface board.

64 IO LVDS
28 IO SE
2 CLK_IN LVDS (FPGA PIN H19,H20 ; H18,J17) and SE (FPGA PIN J20 ; J16)
2 CLK_OUT LVDS (FPGA PIN U31,U32 ; AC3,AB2) and SE (FPGA PIN J21 ; J15)

RAM¶

A 64 bit DDR2 SODIMM connector provides high speed memory connection to the APPSFPGA. Memory
controller design for the APPSFPGA is not included. For a memory controller reference design
Xilinx Memory Interface Generator (MIG) User Guide [ug086.pdf]

USB¶

The USB EEPROM does not have any code only VID/PID data. Here is a sequence of USB initialization:

When a board is plugged in by USB the Windows D4100 USB driver sees the unprogrammed TI VID/PID.  (The Windows D4100 USB driver is installed with the Explorer software.)
    Then it loads a program directly into the Cypress USB (not the EEPROM) and runs it.  (This loads the firmware through USB)
    This sets the Cypress VID/PID to show that the part is programmed and allows communication with the Board.

This is only the first part. To communicate with the DMD a different APPS_FPGA program (D4100_GUI_FPGA.bin) must be loaded that can communicate with the Cypress USB.

When the D4100 Explorer is started it checks to see if D4100_GUI_FPGA.bin is loaded in the FPGA and programs the FPGA if it not.

This program can also be loaded by invoking the DLL function directly from another program (see the API Programmer’s Guide)

Once loaded then the other API DLL functions can be used to load and reset image data.

If you have one of the ViALUX ALP versions you will need to contact them concerning this since their software uses proprietary communication protocols with the D4100.