Project

General

Profile

Wiki DLP4100 » History » Version 9

Frédéric Blanc, 2017-04-24 16:42

1 2 Frédéric Blanc
p=. *Wiki DLP4100*
2
 
3
h1. Overview 
4
 
5
The DLP® Discovery™ 4100 (D4100) is the latest in a series of spatial light modulation development kits from Texas 
6
Instruments.  Users of the D4100 Starter Kit have the ability to manipulate visible, ultraviolet and near-infrared light 
7
with extremely high performance and high resolution. 
8
 The D4100 offers developers a flexible platform to design products to fit most any application using the proven 
9
reliability of DLP technology. 
10
11 1 Frédéric Blanc
!D4100_Starter_Kit_Block_Diagram.PNG!
12 3 Frédéric Blanc
Fig 1: System Overview 
13 1 Frédéric Blanc
14 7 Frédéric Blanc
|_.New version 2017|_.Actual|_.Name|
15 6 Frédéric Blanc
|DLPC410|DDC4100 (FPGA X5VLX30)|Digital Controller for Discovery 4100 chipset|
16
|DLPR410|XCF16|PROM for Discovery 4100 chipset|
17
|DLPA200|DAD2000|DMD Micromirror Driver|
18
19 2 Frédéric Blanc
h2. Configuration Jumpers 
20 1 Frédéric Blanc
21 2 Frédéric Blanc
!D4100_Controller_Configuration_Jumpers.PNG!
22
Fig 2: D4100 Controller Configuration Jumpers
23
24 9 Frédéric Blanc
*LED1
25
26
*LED2
27
28
*LED3
29
30
*LED9-12
31 2 Frédéric Blanc
*J2 – EXP Voltage Select*
32
33 8 Frédéric Blanc
*J4 – Used to select the revision of firmware loaded from the PROM to the APPSFPGA.*
34 2 Frédéric Blanc
35
|_.Jumper Position|_.Revision Version|
36
|open|0|
37
|close|1|
38
39
*J5 – Shared USB signal disabled*
40
41
|_.Jumper Position|_.USB Signals|
42
|0-1|Disconnected from FPGA |
43
|1-2|Connected to FPGA|
44
|2-3|Automatically connect USB signals 
45
     to FPGA when USB is connected to 
46
     host PC |
47
 
48
*J7 – USB EEPROM Programming Header* 
49
50
Used to temporally disconnect the USB EEPROM fromthe device so the device can load its internal 
51
boot loader rather than any code in the EEPROM. Install J8 for Cypress internal boot loader. 
52
 
53
*J10 – DAD2000 B Output Enable*
54
55
Used to enable the outputs for DAD2000 B. This needs to be enabled only if using the 1080p DMD, 
56
otherwise this can be disabled. 
57
58
|_.Jumper Position|_.DAD2000 B Outputs|
59
|open|Disabled|
60
|close|Enabled|
61
62 8 Frédéric Blanc
*J11 – Used to select the revision of firmware loaded from the PROM to the DDC4100 (FPGA X5VLX30).*
63 4 Frédéric Blanc
64
|_.Jumper Position|_.Revision Version|
65
|open|0|
66
|close|1|
67 9 Frédéric Blanc
68
*SW1
69
70
*SW2
71
72
*SW3
73
74
*SW4