Wiki » History » Revision 83
Revision 82 (Frédéric Blanc, 2021-10-29 16:17) → Revision 83/223 (Frédéric Blanc, 2021-10-29 16:17)
h1. Station sous pointe Karl Süss AP6
H2. AP6 Châssis
!clipboard-202110251006-k2ziz.png!
!clipboard-202110251011-9vhql.png!
!clipboard-202110251012-p94w0.png!
h2. Contrôleur
!clipboard-202110181528-f7ndu.png!
210AA071-01
h3. 260PC113 Karl Suss 16 Channel Input Card
!clipboard-202110291053-irhn6.png!
260PC113 Karl Suss 16 Channel Input Card
| | BROCHE | ||BROCHE| | BROCHE | ||BROCHE|
| DB25 | 1 | *GND* |J22| 20| DB25 | 14 | |J22|29|
| DB25 | 2 | |J22| 27 | DB25 | 15 | *GND* |J22|18|
| DB25 | 3 | |J22| 25| DB25 | 16 | |J22|23|
| DB25 | 4 | *GND* |J22| 16| DB25 | 17 | |J22|21|
| DB25 | 5 | |J22| 19 | DB25 | 18 | *GND* |J22|14|
| DB25 | 6 | NC || | DB25 | 19 | | *J12* |2|
| DB25 | 7 | *GND* |J22| 12| DB25 | 20 | |J22|17|
| DB25 | 8 | |J22| 15 | DB25 | 21 | *GND* | J22 |10|
| DB25 | 9 | |J22| 13 | DB25 | 22 | |J22|11|
| DB25 | 10 | *GND EYF* |J22| 8 | DB25 | 23 | *EYF* |J22|7|
| DB25 | 11 | |J22| 9 | DB25 | 24 | *GND* |J22|6|
| DB25 | 12 | |J22| 3 | DB25 | 25 | |J22|5|
| DB25 | 13 | *GND* |J22| 4|
h3. 260PC152 Karl Suss VALVE
!clipboard-202110291614-h8car.png!
h2. Connecteurs
!clipboard-202110191431-ftq3o.png!
!clipboard-202110191504-p6tbi.png!
Male vue de dessus
Sub-D FCI 50
!clipboard-202110291524-y1awq.png!
h3. J12 ♂ (mâle)
| | BROCHE | | | BROCHE | | | BROCHE | |
| J12 | 1 | | J12 | 18 | Moteur axe Y B- | J12 | 34 | |
| J12 | 2 | DB25 19 | J12 | 19 | Moteur axe Y B+ | J12 | 35 | |
| J12 | 3 | Moteur axe X A+ | J12 | 20 | Moteur axe Y B+ | J12 | 36 | |
| J12 | 4 | Moteur axe X A+ | J12 | 21 | | J12 | 37 | |
| J12 | 5 | Moteur axe X A- | J12 | 22 | | J12 | 38 | |
| J12 | 6 | Moteur axe X A- | J12 | 23 | Moteur axe Z A+ | J12 | 39 | |
| J12 | 7 | Moteur axe X B+ | J12 | 24 | Moteur axe Z A- | J12 | 40 | |
| J12 | 8 | Moteur axe X B+ | J12 | 25 | Moteur axe Z B+ | J12 | 41 | |
| J12 | 9 | Moteur axe X B- | J12 | 26 | Moteur axe Z B- | J12 | 42 | |
| J12 | 10 | Moteur axe X B- | J12 | 27 | Moteur Theta X A+ | J12 | 43 | |
| J12 | 11 | | J12 | 28 | Moteur Theta X A- | J12 | 44 | |
| J12 | 12 | | J12 | 29 | Moteur Theta X B+ | J12 | 45 | GND |
| J12 | 13 | Moteur axe Y A+ | J12 | 30 | Moteur Theta X B- | J12 | 46 | GND |
| J12 | 14 | Moteur axe Y A+ | J12 | 31 | | J12 | 47 | GND |
| J12 | 15 | Moteur axe Y A- | J12 | 32 | | J12 | 48 | GND |
| J12 | 16 | Moteur axe Y A- | J12 | 33 | | J12 | 49 | GND |
| J12 | 17 | Moteur axe Y B- | | | | J12 | 50 | NC |
h3. J22 ♀ (femelle)
| | BROCHE | | | BROCHE | | | BROCHE | |
| J22 | 1 | NC | J22 | 18 | *GND* | J22 | 34 | NC |
| J22 | 2 | NC | J22 | 19 | | J22 | 35 | NC |
| J22 | 3 | | J22 | 20 | *GND* | J22 | 36 | NC |
| J22 | 4 | *GND* | J22 | 21 | | J22 | 37 | NC |
| J22 | 5 | | J22 | 22 | *GND* | J22 | 38 | NC |
| J22 | 6 | *GND* | J22 | 23 | | J22 | 39 | NC |
| J22 | 7 | EYF | J22 | 24 | *GND* | J22 | 40 | NC |
| J22 | 8 | *GND* EYF | J22 | 25 | | J22 | 41 | NC |
| J22 | 9 | | J22 | 26 | *GND* | J22 | 42 | NC |
| J22 | 10 | *GND* | J22 | 27 | | J22 | 43 | NC |
| J22 | 11 | | J22 | 28 | *GND* | J22 | 44 | NC |
| J22 | 12 | *GND* | J22 | 29 | | J22 | 45 | NC |
| J22 | 13 | | J22 | 30 | *GND* | J22 | 46 | NC |
| J22 | 14 | *GND* | J22 | 31 | NC | J22 | 47 | +5V |
| J22 | 15 | | J22 | 32 | NC | J22 | 48 | +5V |
| J22 | 16 | *GND* | J22 | 33 | NC | J22 | 49 | +5V |
| J22 | 17 | | | | | J22 | 50 | +5V |
h2. Capteur fin de course
!clipboard-202110251609-uyvvh.png!
fourche optique Honeywell S-180-B55
!clipboard-202110280935-peqaw.png!
!clipboard-202110280947-by0u2.png!
*E* Emetteur (diode) *D* Détecteur (phototransistor)
!clipboard-202110280958-0w6t2.png!
h2. Moteurs
Theta et Axe Z
!clipboard-202110191422-xp8dx.png!
ESCAP P520 254 0.7 60
h3. Nouveau câblage
!clipboard-202110251302-x7174.png!
câble moteur AWG23 (0.25mm²,67mOhms/m,)
h3. Nouveau contrôleur axe Z et Theta
DRV8825 Stepper Motor Driver
!clipboard-202110261325-w0k9d.png!
!clipboard-202110251411-xrnym.png!
h3. Nouveau contrôleur axe X et Y
!clipboard-202110251328-xl46h.png!
TB6600 4A DC 9-42V
!clipboard-202110251326-hfzhq.png!
h2. Logiciel pilotage 4 axes
https://github.com/zapmaker/GrblHoming/releases/tag/v3.6.1
Grbl Controller 3.61 de zapmaker pour Windows
https://github.com/fra589/grbl-Mega-5X
Grbl pour Arduino Mega2560
cpu_map.h - CPU and pin mapping configuration file Part of Grbl
!clipboard-202110281149-o7xmm.png!